To install: Click on the haspx. Double-click on the. You must have HASP drivers installed to run this executable. To install: Click on the Nhaspx. Use this product to install Mastercam License Manager. To install: Click on the mastercam-licensemanager. Double-click on mastercam-licensemanager. To install: Click on the mastercam-monitor.
This utility will install the Mastercam Activation Wizard. The program allows the activation of Mastercam products using an activation code. Use this product to install the CodeMeter software necessary to run software licensing for Mastercam. If you receive this, download this file.
To install: Download mastercamx9-b1-codemeter-plugin. Start CodeMeter by clicking on the icon in your taskbar. Open pockets are created from chains that do not have the same start and end point. Mastercam creates an imaginary line between the start and end points of the chain to close the geometry, allowing you to overlap the open area with a percentage of the tool diameter.
Toolpath Preview: Select the first entity in the chain, as shown. For climb milling see page for more details on climb milling , be sure to chain the contour in a CCW direction. Otherwise select the Reverse button. Select the last entity as shown. Note that in the Toolpath Type page the Pocket icon is automatically selected by Mastercam and the Chain geometry shows one 1 chain. Disable Filter Active to see all the tools available in the current tool library.
Scroll down and select the 0. Note that the Feed rate, Plunge rate, Retract rate and Spindle speed are roughly based on Aluminum part material and a carbide tool. Machining Direction set to Climb cuts in one direction with the tool rotating in the opposite direction of the tool motion.
See the graphic below. Pocket type set to Open can be used with open and closed chains. The distance between the start and end points of the open contour is determined and internally Mastercam creates a line to close the chain. Overlap sets the amount that the tool overlaps the open area. Use open pocket cutting method forces the tool to start cutting from the open area, avoiding plunges in the middle of the part. Stepover percentage sets the distance between roughing passes in the XY axis as a percentage of the tool diameter and will automatically update the stepover distance.
Roughing angle sets the orientation for the roughing passes when you use the One Way or Zigzag cutting methods for pocket toolpaths.
Note that the Zigzag cutting method will not be used in this toolpath; instead, the open pocket cutting method will be used as set in the Cutting Parameters page. From the Tree view list, select Finishing. The current settings in the Finish area enables one finish pass of a 0. Enable the box in front of the Depth cuts and change the parameters to divide the total depth in increments not bigger than the tool radius as shown below.
From the Tree view list, select Break Through. Enable Break through and enter the amount to cut through as shown below. Break Through causes the tool to cut through the material. Always enter the break through amount as a positive number. Mastercam adds the break through amount to the final depth of the toolpath to ensure through-cutting.
Enable Clearance and enter the Depth value as shown below. Feed plane value sets the height from which the tool plunge-rates into the part. Top of stock value sets the height of the material. Depth value sets the final machining depth for the pocket operation. Contour toolpaths only follow a chain; they do not clean out an enclosed area. Be sure to chain the contour in a CW direction.
Otherwise, select the Reverse button. Change the parameters to match the following screenshot. Compensation direction set to Left compensates the toolpath to the left of the chain based on the chaining direction. Roll cutter around corners set to Sharp inserts arc moves around corners in the toolpath. The radius of the arc moves is equal with the radius of the tool. Set to None to not create any extra arcs.
Infinite look ahead prevents the toolpath from crossing itself fish tail. Contour ramp type allows you to use a continuous ramp to transition smoothly between depth cuts, instead of individual plunge cuts. From the Tree view list, select Break Through, enable the option and enter the Break through amount as shown below. Multiple cutting passes allows you to follow the contour geometry in steps in the current cutting plane XY.
Setting to 1 the Number of rough passes will remove the material around the outside contour leaving the 0. The finish pass will remove the 0. Typically, when creating a chamfer toolpath, you will set the Depth to 0. Select the contour, as shown. Click on Select library tool button. Select the Filter button. Change the parameters to select only the chamfer mill with the diameter equal to 0.
Select the OK button to exit. Click on the tool to highlight it, and then select the OK button to exit Tool Selection. Select the OK button to accept the warning that tells you that the tool cannot be used for both roughing and finish. Set the chamfer parameters to cut a 0. Tip offset amount ensure that the tip of the tool clears the bottom of the chamfer. From the Tree view list, select Multi Passes and disable the option. From the Tree view list, select Linking Parameters and make the changes as shown below.
Note that the Depth is set to 0 relative to the top of the stock to let Mastercam to calculate the tool depth from the chamfer dimensions. This display lets you spot errors in the program before you machine the part. As you backplot toolpaths, Mastercam displays the current X, Y, and Z coordinates in the lower left corner of the screen. Click on the Toolpath Group in the Toolpaths Manager to select all operations.
Select Toolpath Group 1 Select the Backplot selected operations button. Make sure that you have the following buttons turned on they will appear pushed down. You can adjust the speed of the backplot. You can step through the Backplot by using the Step forward Page or Step back buttons. Select the OK button to exit Backplot. The finished part should appear as shown in the following picture. Select the OK button to exit Verify. Generally, every machine controller will require its own post processor, customized to produce code formatted to meet its exact requirements.
Make sure that all operations are selected, otherwise, Select all operations. Select the Post selected operations button from Toolpath Manager. Cnc Code Maker. Mastercam X5. Mastercam X2. TurnMaster Pro. MT Nethasp Setup for bit Systems. How to recover corrupted image files.
How to transfer all files to a new computer. How to download all files from a Cloud storage. How to transfer files from a Mac desktop to an external hard drive. How to share files on Windows How to Recover Deleted Files on Mac.
0コメント